cell7dotORG : 1991 Accord EX Wagon

[cell7dotORG]

http://www.cell7.org/images/accord3.jpg


Well, I finally picked up my EX, I was not hipped to a few of the body issues until now, they really aren't a problem, this project is still a go. Once I toss the h23 in there (sitting in my friends garage) I should be worlds happier.

ENGINE/PERFORMANCE:
Pivot Vtec Controller
2.5" Full Exhaust w/ N1 Muffler

WHEELS/SUSPENSION:
H&R Race Springs
Neuspeed Strut Tower Bar

EXTERIOR:
stock

INTERIOR:
stock

AUDIO/ELECTRONICS:
stock


Future:
h23 non-vtec
17" rims (not sure style/color, but not chrome)
Sway Bar upgrades

So, away with the pics (leaving out the close ups of damage so I don't have to look at them too much)


http://www.cell7.org/images/accord1.jpg

[accordtunerx]

looks like you had some of that common rust on the rear quarter panel... and it looks like you did some body work to it. it looks primered. did you remove the rust yourself?

[cell7dotORG]

Actually, the bodywork was done on both sides before I got it, but it was never painted so again a little rust, the passenger side is the worse looking. I'll need to do some hefty work on it*, and a couple of small dents in the rear and I'll be ready to paint.

The poor passenger side wheel well :(
http://www.cell7.org/images/accord2.jpg

*not sure I can save much of this side, I will probably be learning to weld by the looks of it. Also I may just cut out the underside on both sides (like rolled, but just removed instead) so I can allow for some more tuck action when bigger wheels are purchased.

[4drcord]

:oops:

[cell7dotORG]

Originally posted by 4drcord
Why do you have a vtec controller

:oops:
I am not sure why you gave me the oops emot. I would suppose it's because this is under my hood, and because it came with the car. ;)

Of course, once I put the h23 in there, the Pivot unit is more of just a glorified A/F unit with no real purpose but the air/fuel... Will probably take it out and use it on my EF9 (after I replace the DOHC ZC with a b16).

http://www.cell7.org/images/accord6.jpg

[chessboxer]

nice grocery getter man, just kidding, just needs some love and it will be sitting pretty. Good luck with future plans.

[accordtunerx]

well.. as far as that quarter panel rust.. i had the same exact problem. i recently did some body work with my dad, and now it's primered and ready for paint. looks great. i took pics of the whole process, and i will post up a DIY very soon. this might be helpful to you if you are considering doing the body work yourself.

[cell7dotORG]

Originally posted by accordtunerx
well.. as far as that quarter panel rust.. i had the same exact problem. i recently did some body work with my dad, and now it's primered and ready for paint. looks great. i took pics of the whole process, and i will post up a DIY very soon. this might be helpful to you if you are considering doing the body work yourself.
That would be very helpful for probably more than just me, if you cannot get around to it, email me the photos jspec@cell7.org and I will post them up for you ;) (with credit to you of course).

[4drcord]

Originally posted by cell7dotORG
I am not sure why you gave me the oops emot. I would suppose it's because this is under my hood, and because it came with the car. ;)

Of course, once I put the h23 in there, the Pivot unit is more of just a glorified A/F unit with no real purpose but the air/fuel... Will probably take it out and use it on my EF9 (after I replace the DOHC ZC with a b16).

http://www.cell7.org/images/accord6.jpg Why are you not sure about the oops emot? there was no indication earlier of your situation with the motor. just because its called oops doesnt mean that i meant "oops". i used it as a expresion for my question. i mean i would have supposed it if you had that pic up first.

[cell7dotORG]

Originally posted by 4drcord
Why are you not sure about the oops emot? there was no indication earlier of your situation with the motor. just because its called oops doesnt mean that i meant "oops". i used it as a expresion for my question. i mean i would have supposed it if you had that pic up first.
I talked to the guy that I bought the car from, I didn't realize that he had swapped in the vtec motor before, I just assumed that all of the EX's at least sported a vtec powerplant (my knowledge of Honda's up until a few weeks ago extended mainly into the Civic models and Integra's). Sorry for the confustion.

[h22wagon]

your finally got it huh cell. looks the same as when i saw it last. i need to post pics of my wagon up and rep for STL and the fact that only 4th gen wagons go fast around hear(their are no othe 4th gens around). time will set that car aside from the rest.

[accordzoom]

if your interested in the 17"s i have on my car , just email me. heres a pic , like month old
JasonB@maab.aorcentaf.af.mil

[619_Cb9]

cool im not the only one on here with a wagon

[exrtuner]

ahhh the wagon.... gotta love em

[brown91coupe]

she a little rough around the edges, but i've always loved the wagons :boink: