CB7Tuner Forums

CB7Tuner Forums (http://www.cb7tuner.com/vbb/index.php)
-   Members' Rides (http://www.cb7tuner.com/vbb/forumdisplay.php?f=42)
-   -   Raf99 : 1993 Accord EX (http://www.cb7tuner.com/vbb/showthread.php?t=139375)

Raf99 07-15-2009 07:33 AM

Raf99 : 1993 Accord EX
 


Big thanks to...
DarkCloud, TypeG, rocketman_471, cb7rush, Theos92VR4(x2), almostJDM, , NightmareCB7, xkjnboix, almostJDM, H23CB7, tommi, 1990[H]accordex, treyd82, dannyd, bmxicansd, STREET-SPEC, 93a-lude, lindiz, DanCan, fleetw00d, Excalibur, Losiracer2 and many others for the help

**Special HUGE thanks to James at Raven Auto Sports in Halifax, NS for helping build, tune, and bring this monster to life!! Without him this car would not be where it is now!!**


http://clevercomputersolutions.ca/cb.../7-30-2015.jpg

http://clevercomputersolutions.ca/cb...029_174006.jpg


410WHP/296TQ @ 17PSI

Engine

JDM H22A engine
Skunk2 intake manifold
Manual tensioner
Darton sleeves
Eagle H rods
Arias forged pistons (8:5:1)
Cometic head gasket
ARP main studs
Cometic lower engine gasket kit
Endyne oil pump
Greddy timing belt
Greddy balancer belt
Mishimoto half radiator
Mishimoto slim radiator fan
Mishmoto power steering reservoir relocation
H22A 68mm throttle body
MSD Ignition system
Walbro 255lph fuel pump
Internal distributor coil mod.
Battery relocation to rear
Fuse Box relocation
Full Wire tuck
Full A/C delete
EGR/Canister full removal
3" Full exhaust w/ Flowmaster muffler (no cat)
18" Resonator

ESP engine mounts
ESP front lower traction bar
ESP 3 point upper strut bar
ESP alternator relocation bracket

Transmission
T2T4 LSD Transmission 5-speed transmission
- Synchrotech bearing set
- Synchrotech carbon fiber sychro set
- Synchrotech F23 shaved 5th gear
- Assco 12lbs flywheel with ARP bolts
- Tilton twin disc racing clutch & pressure plate


Go Gear
GT35R Turbo (.70 compressor, 56trim) w/ oil and coolant lines
Mishimoto Intercooler
Tial 50mm BOV
Tial 44mm WG
Top Mount 44mm Turbo manifold
Precision 880CC Low Impedance injectors
GM 3bar map sensor
S300 V2 ECU with boost control
AEM fuel rail
AEM FPR
AEM A/F ratio gauge
AEM boost controller
AEM boost gauge
Oil pressure gauge
Oil catch / valve cover 2x10an fittings setup
Fast Turbo feed and outlet turbo lines



Exterior
Tein Super Streets
Braided steel brake lines
Rear disc swap
17" DAI Mirage rims w/215/40/17 +38
EBC Front drilled and slotted rotors and pads
EBC Rear drilled and slotted rotors and pads
Front SPC front camber kit
Rear Ingals angle camber kit
Fat Four Customs rear LCAs
Fat Four Customs rear toe arms
Ractive rear upper strut bar
Ractive rear lower tie bar
Clear bumper signal lights
JDM mirrors (in USDM housings)
JDM side marker lights
JDM intersection lights, relays and harness
JDM yellow fog light bulbs
Red/Clear Sedan tail lights
EDM rear fog light

80% tint on rear windows and back window
OEM Window visors
Shaved antenna
Shaved logos
91 DIY front grill
Rear camera DIY into trunk key hole
95 JDM Honda Accord front lip‏
95 Accord EXR rear lip
95 Accord side skirts

CB7 JDM one piece black housed headlights /w
- Yellow high beam shroud
- JDM yellow high beam bulb
- DS2 Mini projectors w/ electronic cut-off shield (theretrofitsource.com)
- Gatling Gun mini shrouds (theretrofitsource.com)
- Phillips 85122 bulbs (theretrofitsource.com)
- 100mm halo rings high beams (theretrofitsource.com)
- 90mm halo rings low beam (theretrofitsource.com)
- Wiring splitters (theretrofitsource.com)
- HID ballast (theretrofitsource.com)
- Headlights shields




Interior

97 Prelude front seats
Black dash swap
Dyed black floor mats
Dyed black mat of rear seat
DIY black interior pieces
Black carpet from stockinteriors.com
Complete DIY trunk redo with black fabric
Silver speedo/RPM/cluster rings with color matched cluster background
Momo steering wheel
Full blue LED gauge/dash conversion


ICE

Alpine IVA-D310 In-dash 7" DVD screen
Alpine IVA-D310 brain unit
Alpine I-Pod interface adapter
Alpine MRV-1507 class D 900W OMS
2 x 400W Clarion 10" subs
Alpine Flex5 MRP-F365 amp
Qlogic corner enclosures w/
-Alpine crossovers
-Alpine 300W 6-1/2" 2-Way component speakers & tweeters
Pioneer 180W 6 1/2" rear speakers
Pioneer 140W 5 1/4" front speakers



If you read this far congrats! This list is getting way too long :)

Future Plans

Carbon fiber hood (do not have..)
Carbon fiber trunk (do not have..)
Black Dash (do not have)
Big Brake upgrade

--
http://clevercomputersolutions.ca/cb...521_205134.jpg
--
http://clevercomputersolutions.ca/cb...722_170313.jpg
--
http://clevercomputersolutions.ca/cb...827_185424.jpg
--
http://clevercomputersolutions.ca/cb...817_180144.jpg
--
http://clevercomputersolutions.ca/cb...222_173036.jpg
--
http://clevercomputersolutions.ca/cb...928_125810.jpg
--




----------
------------------
-------------------------
************************From this point below are pics when I started my MRT. As the pages go on, so do the updates and pics
-------------------------
------------------
----------
-----

PointBlank 07-15-2009 01:18 PM

Love the rims and swap, not feeling the lights all around.

Was that first one an old pic and your back to stock, or are the other ones older pics?

Clean_4th gen 07-15-2009 01:25 PM

http://carphotos.cardomain.com/ride_...0031_large.jpg

http://carphotos.cardomain.com/ride_...0031_large.jpg

Clean! :tu: What size are those wheels? :eyebrow:

19TcappaLX 07-15-2009 09:38 PM

WOW!! bro your cb is nice,love that color.those rims are nice also.got some interior pics.

91f22jon 07-15-2009 10:03 PM

Clean ass motor looks good

Raf99 07-19-2009 12:26 PM

Quote:

Originally Posted by Clean_4th gen (Post 2132580)
http://carphotos.cardomain.com/ride_...0031_large.jpg


Clean! :tu: What size are those wheels? :eyebrow:

They are 17".

kouzie 07-19-2009 09:09 PM

that is one clean mofo......:tu::tu:

vietkid_2006 07-19-2009 11:33 PM

pretty agressive. but clean! Cb :p

trubluryder 07-20-2009 02:54 AM

Damn, that is one clean ass paint. Did you get it resprayed? If not, you took damn good care of it :tu:. Btw Most peeps on here may not like your wheels and or the projectors, but I think they suite your car well. Keep it different yet clean :thumbsup:

Ps. If you want your projectors to put out better output, throw some HID'S in and aim them right. Now if you want even better output, throw some HID's into the fogs also :D:tu:

F20A CB7 07-20-2009 09:02 AM

Clean.

jimmybean21 07-20-2009 04:55 PM

clean cb not really feeling the tail lights, but overall it looks good. is your motor stock or have you done some work to it?

Raf99 07-21-2009 08:03 AM

Quote:

Originally Posted by jimmybean21 (Post 2138782)
clean cb not really feeling the tail lights, but overall it looks good. is your motor stock or have you done some work to it?

Motor is a h22a swap. (see above pic)

F20A CB7 07-21-2009 08:54 AM

http://www.cb7tuner.com/vbb/showpost...3&postcount=33

A cool diy for 1 piece ebay lights.

Raf99 07-22-2009 11:51 AM

Quote:

Originally Posted by F20A CB7 (Post 2139712)
http://www.cb7tuner.com/vbb/showpost...3&postcount=33

A cool diy for 1 piece ebay lights.

Thanks, but my headlights are already blacked out. ( can't wait to do the tail-lights though )

Raf99 07-31-2009 11:15 PM

http://memimage.cardomain.com/ride_i...0078_large.jpg

19TcappaLX 07-31-2009 11:32 PM

man your grill is HOT,i want to do my grill like that when i get her painted.

91ExSedan 08-01-2009 07:10 AM

Swweeeet grill.

Clean_4th gen 08-01-2009 12:25 PM

Quote:

Originally Posted by Raf99 (Post 2137480)
They are 17".

Nice, were they hard to find? :eyebrow:

http://memimage.cardomain.com/ride_i...0075_large.jpg

I like your front end! :tu: Do I spy a 90-91 grille on there? :bouncy:

Raf99 08-10-2009 08:58 AM

Quote:

Originally Posted by Clean_4th gen (Post 2153574)
Nice, were they hard to find? :eyebrow:

http://memimage.cardomain.com/ride_i...0075_large.jpg

I like your front end! :tu: Do I spy a 90-91 grille on there? :bouncy:


thanks :thumbsup: You are correct :) ( I gotta adjust that one headlight though, it looks a tiny bit off )

Raf99 08-10-2009 09:01 AM

Quote:

Originally Posted by 19TcappaLX (Post 2152962)
man your grill is HOT,i want to do my grill like that when i get her painted.

Thanks! Here's the DIY I did for it, enjoy :)
http://www.cb7tuner.com/vbb/showthread.php?t=139188

gloryaccordy 08-10-2009 09:14 AM

Good: Swap, suspension

Bad: Rims, lights

Off to a good start fa sho tho

StinkinLincoln 08-10-2009 10:12 AM

Me Likie!!!

Clean_4th gen 08-10-2009 11:15 AM

Quote:

Originally Posted by Raf99 (Post 2164261)
thanks :thumbsup: You are correct :) ( I gotta adjust that one headlight though, it looks a tiny bit off )

That's nice! :tu: I just got an all-black 90-91 grille! :thumbsup: And it looks a bit off? :eyebrow: I can't tell the difference! :shrug: You should see mine...compared to mine, yours is perfect! :shrug:

Clean_4th gen 08-10-2009 12:56 PM

Quote:

Originally Posted by Raf99 (Post 2164430)
I mean the left headlight (in the pic) is a bit off. It needs to be lowered a bit.

I can't tell the diff but if you say so! :shrug: Lol :evil:

Clean_4th gen 08-11-2009 11:35 AM

Quote:

Originally Posted by Raf99 (Post 2164680)
Hey man, what's with your signature saying 92-93 center console for sale?

It's a 92-93 center console I have for sale in the classified section. :thumbsup: Click on it(it's a link)! :tu:

Raf99 08-19-2009 09:49 AM

Quote:

Originally Posted by Clean_4th gen (Post 2165768)
It's a 92-93 center console I have for sale in the classified section. :thumbsup: Click on it(it's a link)! :tu:

I did, it asks for a password. I tried my pass but it was a no go. :confused:

Clean_4th gen 09-21-2009 10:18 AM

Quote:

Originally Posted by Raf99 (Post 2175190)
I did, it asks for a password. I tried my pass but it was a no go. :confused:

Read the sticky at the top of the page! :thumbsup:

benjerman112 10-22-2009 12:28 AM

nice bro, like everything bout the car! change is good.:thumbsup:

93SM4_CB7 10-24-2009 12:19 PM

i Envy how clean your cb's body is and how fresh that paint looks :tu:

Raf99 10-28-2009 03:53 PM

Quote:

Originally Posted by 10thAnnCB7 (Post 2271495)
i Envy how clean your cb's body is and how fresh that paint looks :tu:

Thanks man. Your car is still looking clean, I like the red/clears tail-lights, i'm just not sure if I wanna make the transformation yet to them.

Raf99 11-10-2009 11:51 PM

I've been working on cleaning up the engine bay. Took some pics.

http://carphotos.cardomain.com/ride_...0086_large.jpg
--
http://carphotos.cardomain.com/ride_...0088_large.jpg

19TcappaLX 11-10-2009 11:56 PM

very nice, looks really clean.good job on the swap.

http://carphotos.cardomain.com/ride_...0088_large.jpg

Clean_4th gen 11-11-2009 08:32 AM

Looking good man! :tu: When are we going to swap wheels? :evil:

Raf99 11-11-2009 09:52 AM

Quote:

Originally Posted by Clean_4th gen (Post 2298409)
Looking good man! :tu: When are we going to swap wheels? :evil:

thanks
...haha, you don't want these wheels. I'm not sure what to do with them. They are almost 3 years old now and are coroding under the clear coat and getting pretty bad on one of them. The passenger rear need air in the tire about once a month, I'm guessing its a hair-line crack. And I can't find a place that still stocks these, so I can't replace any of them.

By next summer I am going to have new rims and so I need to decide what to do with these. I'm thinking of sanding them down myself and making a project out of them.

Clean_4th gen 11-11-2009 09:58 AM

Quote:

Originally Posted by Raf99 (Post 2298486)
I'm thinking of sanding them down myself and making a project out of them.

That's a good idea! :D What color would you paint them? :bouncy:

Raf99 11-11-2009 11:28 AM

Quote:

Originally Posted by Clean_4th gen (Post 2298491)
That's a good idea! :D What color would you paint them? :bouncy:

I'd paint them the same color that they are now, but i'd add green highlights in where the lugnuts go in. Acadia green obviously. Just something subtle. But I'm not sure if these can be sanded down or not.

Clean_4th gen 11-23-2009 09:45 AM

http://johnheal.ca/gallery2/main.php...serialNumber=1

Quote:

Originally Posted by Raf99 (Post 2298566)
I'd paint them the same color that they are now, but i'd add green highlights in where the lugnuts go in. Acadia green obviously. Just something subtle. But I'm not sure if these can be sanded down or not.

It might take you a long time but I'm sure it can be done! :tu: Looking good BTW! :thumbsup:

Raf99 11-25-2009 08:22 AM

Quote:

It might take you a long time but I'm sure it can be done! :tu: Looking good BTW! :thumbsup:
Thanks. Next summer is going to be a big change. Now that the H22A is in and paint is done the time has come. New rims for sure, I'm going to stick with the black and chrome look for the rims, I just want them to stand out! Maybe more chrome than black instead of more black than chrome, like these: (i still have to do up some photoshop pics)

http://cdn3.ioffer.com/img/item/110/...2vGQGXvCUB.jpg
--
http://imagehost.vendio.com/a/237341..._BLK_RED_1.jpg
--
http://www.driveaccord.net/forums/at...1&d=1241021862
--
http://www.d2autosport.com/wheels/br...ytonspirit.jpg


Its such a hard decision because rims make or break a car! And at the same time non-black rims look cool too.
and either a body kit or a lip kit/side skirts. Currently I'm thinking a lip kit and side skirts; it wouldn't seem right to get a body kit unless I boosted the H22A; which costs a sh*t load of $$$ so that may have to wait.

Also there has to be something I can do to make this thread better though. I guess more pics and DIY pics. I'd like to get some ratings, any thoughts?

jova1993cb 11-25-2009 10:57 AM

a lil bit lower in the front but it is hot:tu:

Clean_4th gen 12-18-2009 08:44 PM

http://imagehost.vendio.com/a/237341..._BLK_RED_1.jpg

My favorite style! :thumbsup: And congrats on the swap! :tu:


All times are GMT -5. The time now is 12:28 AM.

Powered by vBulletin® Version 3.7.1
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.