CB7Tuner Forums

CB7Tuner Forums (http://www.cb7tuner.com/vbb/index.php)
-   Technical (http://www.cb7tuner.com/vbb/forumdisplay.php?f=74)
-   -   F22A1 and F22A6 camshaft specs (http://www.cb7tuner.com/vbb/showthread.php?t=201294)

wagon-r 09-16-2013 08:02 PM

F22A1 and F22A6 camshaft specs
 
As explained in a post I put up a few minutes ago, I purchased used F22A1 and F22A6 camshafts and degreed them.

I degreed them on the head, not the block, but the results should be the same. I set the valve lash to zero, so all measurements are of actual valve lift, and I measured lift at the top of the valve retainer.

Following are the valve lifts and duration that I measured. All durations are at 0.050" valve lift.
............................F22A1....F22A6
Exhaust lift.............0.350"....0.365"
Intake lift...............0.350"....0.365"
Exhaust open BBC.....30..........36
Exhaust close ATC....-18.........-18
Intake open BTC.......-13........-13
Intake close ABC........23.........29

Calculated
Exhaust duration......192........198
Intake duration........190........196
Exhaust center.........114........117
Intake center...........108........111
Lobe separation........111........114
Advance....................3...........3
Degrees overlap.......-31.........-31

What I find interesting is that Honda chose to extend the duration (6 degrees) by increasing the intake/exhaust lobe separation. Exhaust close and intake opening, and hence valve overlap, are unchanged.

Anyway, I hope someone finds these useful.

P5ylance 09-26-2013 01:49 AM

i love information!

and you have the bisi lvl 2 specs as well right? i'd like to see them side by side

HappyGilmore 09-26-2013 05:42 AM

New sticky coming soon? I think so! I been looking into a cam as well. I would like to know what's out there, I want to get maybe 300 out of my F22A1 someday. Would be kinda nice, even better without boost!

deevergote 09-26-2013 07:48 AM

Stuck until we can integrate it into the useful info thread. Nice work!

mugencivic4dr 09-26-2013 12:12 PM

i wish i knew what this info meant. cam specs is something that i always wanted to know about but can never find the time to "study" it :/

jdm92_accorn 09-26-2013 12:45 PM

Here's the new bisimoto level2 specs
Exhaust lift................. .403"
Intake lift.................... .389"
Exhaust open BBDC..... 41
Exhaust closes ATDC... 1
Intake opens BTDC....... 4
Intake closes ABDC...... 44

Calculated @.050"

Exhaust duration.......... 222
Intake duration............. 228
Exhaust center............. 110
Intake center................ 110
Degrees overlap........... 5

Joey GT-R 09-26-2013 01:08 PM

Quote:

Originally Posted by mugencivic4dr (Post 3169461)
i wish i knew what this info meant. cam specs is something that i always wanted to know about but can never find the time to "study" it :/

http://www.cb7tuner.com/vbb/showthread.php?t=197390

You've been served....

bobbycos 09-26-2013 01:32 PM

Quote:

Originally Posted by Joey GT-R (Post 3169470)

thank you for a good thread

wagon-r 09-26-2013 04:25 PM

Quote:

Originally Posted by jdm92_accorn (Post 3169465)
Here's the new bisimoto level2 specs
Exhaust lift................. .403"
Intake lift.................... .389"
Exhaust open BBDC..... 41
Exhaust closes ATDC... 1
Intake opens BTDC....... 4
Intake closes ABDC...... 44

Calculated @.050"

Exhaust duration.......... 222
Intake duration............. 228
Exhaust center............. 110
Intake center................ 110
Degrees overlap........... 5

Nice post. However, I think you mixed up the intake and exhaust lift.


All times are GMT -5. The time now is 03:47 AM.

Powered by vBulletin® Version 3.7.1
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.