CB7Tuner Forums

Go Back   CB7Tuner Forums > Search Forums

Showing results 1 to 11 of 11
Search took 0.00 seconds.
Search: Posts Made By: soybean
Forum: Beginner Appearance 11-17-2012, 11:04 PM
Replies: 9
Views: 1,042
Posted By soybean
No, that was it's position before I attempted to...

No, that was it's position before I attempted to remove it. I had to pry down on the molding so that it could be persuaded forward with a rubber mallet. Then, it came off.
Forum: Beginner Appearance 11-17-2012, 04:15 PM
Replies: 9
Views: 1,042
Posted By soybean
So, pry it out/down with enough force to make it...

So, pry it out/down with enough force to make it clear the bottom of the wheel well and then knock it forward, right?
Forum: Beginner Appearance 11-17-2012, 03:35 PM
Replies: 9
Views: 1,042
Posted By soybean
Well, I discovered I can't knock the molding...

Well, I discovered I can't knock the molding forward because it has a lip at the back up which comes up above the bottom of the wheel well and there's almost no space there between the lip and the...
Forum: Beginner Appearance 11-09-2012, 09:58 PM
Replies: 9
Views: 1,042
Posted By soybean
OK, good info. Thanks much. :)

OK, good info. Thanks much. :)
Forum: Beginner Appearance 11-09-2012, 08:46 PM
Replies: 9
Views: 1,042
Posted By soybean
how to remove rocker panel molding

Back in 2010, I went to body shop to have the rocker panel molding on the driver's side removed. Before going there, I had removed the front wheel mud guard that covers the front end of the rocker...
Forum: Beginner Appearance 11-08-2012, 02:50 PM
Replies: 19
Views: 2,758
Posted By soybean
Well, I don't believe it absorbs moisture out of...

Well, I don't believe it absorbs moisture out of the air but I might apply primer and paint to it on the inside of the trunk as a way of sealing it there. And, on the underside, where the direct...
Forum: Beginner Appearance 11-07-2012, 02:15 PM
Replies: 19
Views: 2,758
Posted By soybean
And, why won't it last?

And, why won't it last?
Forum: Beginner Appearance 11-04-2012, 03:29 PM
Replies: 19
Views: 2,758
Posted By soybean
Since this car is your DD, that will probably...

Since this car is your DD, that will probably present some limitations in the extent of what you can do. I would remove the rear bumper molding so that you can get a clear view of the damage...
Forum: Beginner "Off Topic" 10-28-2012, 02:48 PM
Replies: 255
Views: 15,619
Posted By soybean
Just over 299K miles on my 91 Accord. Manual...

Just over 299K miles on my 91 Accord. Manual transmission; original engine and even the clutch, too.
Forum: Beginner Appearance 10-28-2012, 12:44 PM
Replies: 12
Views: 1,181
Posted By soybean
I used Bondo to repair a hole through the quarter...

I used Bondo to repair a hole through the quarter panel. I did that about 2 years ago and it has held up fairly well. To repair larger holes, a metal mesh backing is really needed to support the...
Forum: Beginner Technical/Performance 10-28-2012, 11:33 AM
Replies: 2
Views: 864
Posted By soybean
You don't need to pull out the motor. You need to...

You don't need to pull out the motor. You need to remove the timing belt cover. Beyond that, I can't provide details regarding what parts need to be removed to get the water pump off. I found a...
Showing results 1 to 11 of 11

 
Forum Jump

All times are GMT -5. The time now is 02:57 AM.


Powered by vBulletin® Version 3.7.1
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.