CB7Tuner Forums

Go Back   CB7Tuner Forums > Search Forums

Showing results 1 to 25 of 500
Search took 0.06 seconds.
Search: Posts Made By: fleetw00d
Forum: Technical Yesterday, 07:28 AM
Replies: 9
Views: 96
Posted By fleetw00d
Did you install a new seal as well?

Did you install a new seal as well?
Forum: Technical 10-13-2018, 07:09 PM
Replies: 9
Views: 96
Posted By fleetw00d
You need new seal and the retainer:...

You need new seal and the retainer: 06923-P0A-306

Found a picture in another thread:

https://ww2-secure.justanswer.com/uploads/CL/clmcr8/2014-04-25_043125_newbshaftsealretainer.jpg
Forum: Off Topic 10-12-2018, 10:34 PM
Replies: 11
Views: 114
Posted By fleetw00d
And all you wound up with was the black rubber...

And all you wound up with was the black rubber trim? Last one I had installed they gave me $50 off because they couldn't remount the original trim (I was able to later).
Forum: Beginner "Off Topic" 10-12-2018, 09:33 PM
Replies: 9
Views: 109
Posted By fleetw00d
The issue with the door may be the hinges. Did...

The issue with the door may be the hinges. Did you just bolt up the door without attempting to adjust the fit at the hinges - there is some play at both mounting points. If the hinge is worn, the...
Forum: Technical 10-11-2018, 04:09 PM
Replies: 9
Views: 96
Posted By fleetw00d
Did you do the timing and balance shaft belts...

Did you do the timing and balance shaft belts while you had it apart? Replace the cam, crank, and balance shaft seals? The most likely culprit is the forward balance shaft seal; they have a...
Forum: Beginner "Off Topic" 10-10-2018, 04:13 PM
Replies: 9
Views: 109
Posted By fleetw00d
If he was swapping doors, I've found that the...

If he was swapping doors, I've found that the wiring is different between 90-91 and 92-93. The doors can be swapped, but you need to swap the harness also.
Forum: Beginner Image Gallery 10-10-2018, 04:05 PM
Replies: 6
Views: 112
Posted By fleetw00d
Welcome! Are these the two hiptech posted about...

Welcome! Are these the two hiptech posted about a while ago? I thought the SE only had 50,000 on it? Decided not to sell or couldn't get a reasonable price so you kept them? Beautiful examples -...
Forum: Technical 10-07-2018, 10:45 PM
Replies: 4
Views: 55
Posted By fleetw00d
I have a 2nd edition in pretty good shape. Never...

I have a 2nd edition in pretty good shape. Never had a first so I can't compare. Mostly I use my 93 manual, which by now is well used.
Forum: Off Topic 10-05-2018, 09:41 PM
Replies: 5
Views: 80
Posted By fleetw00d
90 LX just turned 373k on the body, about 142k on...

90 LX just turned 373k on the body, about 142k on the engine.
93 LX CB9, 253k
92 EX coupe, 171k
92 EX couipe, 190k
Forum: Technical 10-04-2018, 09:34 PM
Replies: 8
Views: 117
Posted By fleetw00d
If I remember correctly, it is the valve in the...

If I remember correctly, it is the valve in the lower duct upstream of the filter box that opens at 3500 rpm, otherwise the lower duct is only connected to the resonator in the fender.

The...
Forum: Beginner Image Gallery 10-02-2018, 10:09 PM
Replies: 3
Views: 75
Posted By fleetw00d
Go ahead an do it. I've even done them for cars...

Go ahead an do it. I've even done them for cars I'm simply rescuing and don't intend to keep. I've even thought about putting together a brief one for cars I've owned and sold just to document them.
Forum: Technical 10-02-2018, 10:03 PM
Replies: 8
Views: 117
Posted By fleetw00d
The bolt you're talking about is the one toward...

The bolt you're talking about is the one toward the back of the manifold at the top of a long bracket from the block? Based on your profile, you have an EX, so I assume you still have the F22A6. ...
Forum: Beginner Technical/Performance 10-01-2018, 11:12 PM
Replies: 15
Views: 347
Posted By fleetw00d
You can swap the cam without worrying about the...

You can swap the cam without worrying about the spring keepers on the valves - it is only if you want to swap the valve springs themselves that you would need a way to keep the valves from dropping...
Forum: Technical 10-01-2018, 10:53 PM
Replies: 1
Views: 48
Posted By fleetw00d
If your compression is good, it is not bent on...

If your compression is good, it is not bent on the bottom end. I had this happen to one of my rescue projects. After having the head cleaned and checked and new valve seals installed; I reinstalled...
Forum: Technical 10-01-2018, 10:48 PM
Replies: 9
Views: 102
Posted By fleetw00d
If a brake is dragging, it will heat up the rotor...

If a brake is dragging, it will heat up the rotor and even the wheel; if it is really bad, it will start smoking because the pad(s) are getting REALLY hot. How old is your brake fluid? Maybe check...
Forum: Beginner Technical/Performance 09-29-2018, 11:41 PM
Replies: 10
Views: 121
Posted By fleetw00d
Did you check your battery connections? Both at...

Did you check your battery connections? Both at the battery and the negative cable connection to the transmission housing?
Forum: Beginner Technical/Performance 09-28-2018, 10:13 PM
Replies: 2
Views: 67
Posted By fleetw00d
The transmission issue may be because of the lack...

The transmission issue may be because of the lack of a VSS signal. I'm assuming the drive key was in there between the power steering VSS and the electrical VSS. Trace the wires and verify whether...
Forum: Technical 09-26-2018, 11:39 AM
Replies: 8
Views: 117
Posted By fleetw00d
If you are going to all the effort of taking it...

If you are going to all the effort of taking it off to clean it, I suggest removing the throttle body (need a new gastket) to make cleaning it easier. Get a new o-ring for the idle screw as well. ...
Forum: Technical 09-24-2018, 11:27 AM
Replies: 4
Views: 62
Posted By fleetw00d
http://www.cb7tuner.com/vbb/showthread.php?t=20320...

http://www.cb7tuner.com/vbb/showthread.php?t=203209

You have to be careful even getting one from a wrecked car. I bought a running parts car 2 years ago (hit hard left rear) that was reportedly...
Forum: Appearance 09-22-2018, 10:22 AM
Replies: 2
Views: 73
Posted By fleetw00d
As an SE, it should originally have had tan...

As an SE, it should originally have had tan leather seating throughout. The original leather doesn't age well unless very well take care of. It is likely they swapped in cloth seats from an LX or...
Forum: Beginner Image Gallery 09-21-2018, 09:11 PM
Replies: 4
Views: 199
Posted By fleetw00d
When you say frame damage, do you mean the actual...

When you say frame damage, do you mean the actual structure of the body, or the cross members? The cross members can be replaced and the body structure can be straightened on a frame rack - don't...
Forum: Members' Rides 09-20-2018, 10:03 PM
Replies: 7
Views: 182
Posted By fleetw00d
Is that the one hiptech posted about back in June?

Is that the one hiptech posted about back in June?
Forum: Other Automotive Members Rides 09-19-2018, 11:53 AM
Replies: 350
Views: 37,010
Posted By fleetw00d
Aren't those going to be very noisy with the...

Aren't those going to be very noisy with the large tread lugs?
Forum: Beginner Technical/Performance 09-16-2018, 09:32 PM
Replies: 8
Views: 143
Posted By fleetw00d
It was probably standard for 94+. It should be...

It was probably standard for 94+. It should be added to 90-93 when the opportunity presents itself. If the seal pops out (I had it happen on one of mine), it will drain the oil in a hurry.
Forum: Beginner Technical/Performance 09-15-2018, 08:13 PM
Replies: 8
Views: 143
Posted By fleetw00d
There is a window to the flywheel/flexplate...

There is a window to the flywheel/flexplate (manual/auto) just below where the engine model (F22A1) is stamped on the block. There is supposed to be a white mark at #1 TDC. The red mark is 15 BTDC....
Showing results 1 to 25 of 500

 
Forum Jump

All times are GMT -5. The time now is 07:41 PM.


Powered by vBulletin® Version 3.7.1
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.