CB7Tuner Forums

Go Back   CB7Tuner Forums > Beginner forum -- New members post here! > Beginner Appearance

Thread Tools Rate Thread Display Modes
Old 04-05-2018, 05:03 PM   #1
Join Date: Apr 2017
Location: Burnaby, BC, Canada
Posts: 3
Yodamaster is cool... so far.
Any source for inner wheel housings?

I'm in the process of fixing the rust on my 91' Coupe, but I'm having a problem finding a replacement inner wheel tub for both sides. The factory part is NLA unless I want to pay $300 per, which is no bueno. I already have replacement outer panels, but those are the easy part...

Am I going to have to scavenge for replacements at yards? They're probably going to have the same problem...
Yodamaster is offline   Reply With Quote
Old 04-05-2018, 08:10 PM   #2
Contributing Member
Join Date: Mar 2007
Location: West Chester, Ohio
Posts: 2,492
fleetw00d is very helpful fleetw00d is very helpful
If that's all the worse it is, just fashion some local patches. Otherwise, as you say, you'd need to scavenge from another car - or have someone down south here cut some out and send them to you. My 90 sedan was a lot worse; I was able to get both the outer and inner from a single car for $100 per side. The outer half of the wheel tub is part of a much larger piece. The thread below shows how I went about replacing the rusted part of mine.

90 LX 4dr 5 spd 368,000 - MRT: http://www.cb7tuner.com/vbb/showthread.php?t=201450
93 LX wagon auto 249,000 MRT:http://www.cb7tuner.com/vbb/showthread.php?t=208490
92 EX coupe auto 168,000 - MRT:http://www.cb7tuner.com/vbb/showthread.php?t=205114
92 EX coupe auto 190,000

LOTS of CB7 parts for sale http://www.cb7tuner.com/vbb/showthread.php?t=192583 or watch for banner ad at upper right

Last edited by fleetw00d; 04-05-2018 at 08:21 PM.
fleetw00d is offline   Reply With Quote
Old 04-22-2018, 03:17 PM   #3
CB7tuner Member
Join Date: Aug 2017
Posts: 71
yh61r is cool... so far.
I'm in the same boat. I'm going to weld the inside directly to the outside. In my opinion, this is much better than having two sheets on top of each other because there's no room for mud and moist to pile up and cause rust, again. Between two sheets is where rust starts, 99% of the time.
yh61r is offline   Reply With Quote
Old 05-16-2018, 06:47 PM   #4
Join Date: Apr 2017
Location: Burnaby, BC, Canada
Posts: 3
Yodamaster is cool... so far.
I decided to just wing it and fashion some patch panels myself, takes a lot of time to get them looking somewhat OEM instead of just slapping metal in. It's VERY difficult to weld in there without having the entire quarter panel off, not much room to maneuver the MIG torch. Temporarily mounted the bumper to check alignment, looks good!

Last edited by Yodamaster; 05-16-2018 at 06:50 PM.
Yodamaster is offline   Reply With Quote

Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

All times are GMT -5. The time now is 04:24 AM.

Powered by vBulletin® Version 3.7.1
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.