So after 3 years of being in this house i decided to replace the ugly, cheap laminate flooring the previous owner installed before she left. My first surprise came when i pulled the first pieces of laminate off the floor; she poured so much damn adhesive and without proper preparation that there was mold under the laminate(every single inch on it). After taking a whole day to scrape the adhesive off the floor and begin to prepare for tile installation came the second surprise; the floor is so wavy that it is ridiculous(how wavy could it be you might ask, as wavy as a mexican soccer match). I was counting on being done with this project this weekend but as my history goes, there seems to always be some kind of shiet happening to my; i feel like a human version of Wiley Coyote. I was excited to start this project because it was the first time my wife was gladly taking part on it but even that went sideways as she managed to step on the only nail facing up on the floor. Yall's boy is done for the day though, i normally push through but its too much work for one person not to mention my dewalt grinder and drill got rained on while i was inside laying tile. Sorry brothers but i had to get it off me.
Announcement
Collapse
No announcement yet.
Flooring rant
Collapse
X
-
Keep after it.
What type of floor was the laminate flooring place on? I'm assuming the concrete slab? If so, I would invest in a decent laser level and grab a cheap stringline. Find the corner of the room that looks the highest and measure up from the subfloor enough room for a thin layer of grout and the thickness of the tile. That can be your top of tile marker. Shoot that elevation across the room, mark that spot on the opposite wall and run a stringline from those two points. Then you can go to a perpendicular wall and shoot the laser across that distance. If the laser is level and the light is hitting the stringline running perpendicular to it, then it's at the same exact elevation with no slope. Set a stringline in the same way you did before. I recommend just stapling the string to the drywall, unless you can manage to get some tape to hold it.
You can do the same thing diagonally across the room if you want to be thorough, but you've now established a common elevation to match where the highest point in the room was. Measure down from the string in a few areas to determine how far off you are. You can even keep the string in place as a measure when applying the grout so that you know how thick you need to leave the mud in the bad spots. I'd recommend the strongest stuff you can get simply because it's now having to provide strength to the floor instead of just acting as a bonding agent.My Members' Ride Thread - It's a marathon build, not a sprint. But keep me honest on the update frequency!
-
I was doing something similar but using a simple level, at one point I had planned to put vinyl in the garage but didn't because of the same reason(wavy floor). It's ridiculous how thick I have to lay in some areas to keep it level. This will definitely take DAYS to do, and will be a miracle if I can get it close to leveled but at least the room seems square so at least I have that going for me.
Comment
-
hack jobs
The hack jobs you find on old cars pale in comparison to the hack jobs you find on old houses.
House projects are like car projects in the respect if you just want to live in it or just drive it, you need to find one that was maintained professionally or by a meticulous owner. If you want a full on custom find one that's a shell. It's never a good idea to buy someones project or "maintained" by the owner.(unless the fall into the the meticulous category)CB7TUNER.com
Educating each other one car at a time.
Comment
-
Originally posted by Raf99 View PostMost times you have to rip it up to the concrete/studs to make everything level again.
Originally posted by deevergote View PostUgh, I hate glued-down laminate. I want to install some laminate in my kitchen and dining room, but I plan to use floating planks over the existing linoleum. If the next owner doesn't like it, they can remove it pretty painlessly!
http://www.sears.com/roberts-airguar...FdERgQodXeEPmQ
Do the prep work right and laying the floor is easy if you are just going to float over the old floor.Originally posted by wed3kim a douchebag to people and i don't even own a lambo. whats your point? we, douchbags, come in all sorts of shapes and colours.
Comment
-
Originally posted by toycar View PostOnly honest/permanent way to handle the job right here
Use a good underlayment and you'll be just fine. I prefer the antimicrobial stuff you can get now like this:
http://www.sears.com/roberts-airguar...FdERgQodXeEPmQ
Do the prep work right and laying the floor is easy if you are just going to float over the old floor.
Comment
-
ya, i'm not sure what you are working with here (concrete floor, multi-level house, etc.) but don't go with a pro unless you have the $$$. They will want to do it right and will either rip up the subfloor and install joist to re-level or use concrete. If the 1" offset is not noticeable I would just clean up the subfloor the best you can and install the new floor. It will look great and no-one will notice a thing. Plus when you spill stuff it will pool in one spot for ya
Comment
Comment