lilb_1979 : 1992 Accord LX

[lilb_1979]

ok, so once again I have to replace my drivers side wheel bearing...... I made a mistake the last time I did it by buying cheap eBay parts. So before everyone gets on me for doing that, I ONLY did it cause I wasnt expecting to DD this all summer long and last year when I did this I had very low funds and winter was very close! I just needed it back on the road again. Ok, so since I did buy cheap eBay front wheel bearing/Hub Assembly's for both sides I only did the drivers side. Now sice I did the cheap parts I cant even get the damn wheel off! I turned a couple of time on 3 of 4 studs and the 3 the stud turns, so now its parked again. I have new parts to fix it, but I need to get the damn wheel off! lol! So, I guess this what I get for getting the cheep parts. Mad, yes I am, but I kinda deserve it for thinking that eBay cheap parts would work. ok, I'm gonna be dumb again and use the other eBay hub.. BUT I got new better high quality studs and I'm just gonna throw the one on there. I got my impact and I hope that tomorrow I can get the lugs off that way. Wish me luck! I will update you guys tomorrow and post some pics of the rusty CB9 them too. One good thing is that this gave me a good reason to drive the cappuccino again for the 2nd time this year. Oh how I miss driving it. lol

[lilb_1979]

Well all fixed!! No more humming!! I think what caused this was the shield around the rotor fell off and was just dangling there. Damn MN rust!! Got NEW brake pads in and it stops better then ever!! I still need to do the Brake master cylinder, but that will have to wait. I didn't take any pics... Who wants to see a dirty CB9 that hasn't been wasted since January 2011 and has MN rust??? lol

[lilb_1979]

ok, just took this..

[lilb_1979]

Well its now Rusty's time!!
Project Blackhouse/Retro #2!!



I also found a set of H&R lowering springs in my basement too, If I'm still gonna drive this next spring/summer I will install them then.

[lilb_1979]

Got all the trimming cut and headlights cleaned up, tomorrow I will be blackhousing them.





These pics where before the cleaning.

[lilb_1979]

[lilb_1979]

All taped up and ready for paint!!




Going to paint right now!!

[lilb_1979]

All Painted!!!!

[F20A CB7]

Sick. Does that projector have a halo ring to it.

It looks like u just popped it in, ppl use shrouds and stuff. I like it better ur way.

Ok no halo ring and looks like some kinda shroud is there... how do u no its even? The lightin output

[lilb_1979]

Yes there is a gatlin shroud. Once the hid's come I will mount everything BEFORE I seal them up to adjust everything if needed. Then its just a matter of sealing them up and putting them on the CB9 for good.

[lilb_1979]

Well here they sit until I get the HID's in. All ready to test!

[lilb_1979]

Here is KINDA what the finished light will look like. The glass is just sitting in there and not sealed up yet. This as far as I can go till the HID's arrive in 3-7 business days.

[Junior Smurff]

Here is KINDA what the finished light will look like. The glass is just sitting in there and not sealed up yet. This as far as I can go till the HID's arrive in 3-7 business days.

Soooo dope!!! I'm hoping to do this once I set a set of spare headlights

[lilb_1979]

Thats the way to go!! I still have a spare set of 90-91 headlights and another set of projectors just sitting downstairs.

[lilb_1979]

Here are the test pics I took today, Tomorrow the final pics will be up!

Test pics before sealing them up for good





















FINAL PICS UP TOMORROW!!!