Socal Whats new with your RIDE?

[ikayto]

paint looks nice, how much were you charged?

Did you paint the cf hood also? Are you going to install the fogs?

I wonder what lip you bought hmm.

[Davids92Accord]

paint looks nice, how much were you charged?

Did you paint the cf hood also? Are you going to install the fogs?

I wonder what lip you bought hmm.

yea they did a great job they painted everything inside and out in total it came out to $2715 just because i told them to buy me new mud flaps new whether stripping paint my molding and a bunch of other stuff and no i i didnt paint the CF hood i still have it i might install it before the next meet both the hood and the trunk im in no rush the paint looks good so im just gonna give it sometime

[4CYLPOWER92]

Nice man who painted it?

[jhondayaaj]

Nice man who painted it?

x's 2....... looks really good david.

[Davids92Accord]

Nice man who painted it?

I took it to westcoast auto body there located on the corner of redondo and Venice they did a great job I'm very satisified

[GHOST 2.2]

i just ordered all these today

31499 OIL SEAL (40X52X7) (NOK) $5.12
18237 OIL SEAL (29X43X8) (ARAI) $4.35
4870643 BELT, TIMING (155YU24 A-555) $51.69
31429 BELT, BALANCER TIMING (UNITTA) $31.46
31475 GASKET, OIL PUMP (A) $2.59
32281 WATER PUMP (YAMADA) $60.75
4870793 ADJUSTER, AUTOMATIC 68.85
31501 OIL SEAL (27X40X8) (NOK) $4.78
51225-SL5-003 BOOT, BALL DUST (LOWER) $10.11
53546-S30-005 BOOT, TIE ROD END $8.65

anyone know how to install a tie rod boot? as well as the boot for the lower knuckle?

[youngJAY]

looks like i have a bad oil leak

[BOOSTIN_DC2]

New shoes for my ce1:

[ikayto]

@ jay snap, is it from your tubro?

@boostin dc2,

those wheels look great on there, what are they?

[bacal36]

[timmy0tool]

anyone know how to install a tie rod boot? as well as the boot for the lower knuckle?

yeah man. this goes for both tie rod and knuckle. just remove the old boot and clip, clean the crap outta the joint, slap some grease onto the joint like a volcano, then put the boot over the grease/joint. then with a needle nose put the circular clip in the middle where the pivot is, open the plier and put over the boot/joint from the top (imagine your girl's legs split on top of you while your balljoint... ), then push the cir-clip downwards until it sits on the groove at the bottom of the boot to lock. get it? the pliers helps keep the cir-clip open over the boot until the bottom.

[GHOST 2.2]

thanks tim. im trying to visualize it, but id have to do it hands on to get it.
i appreciate it timbo. how hard was it to do?

i have 4 of them to tackle. the first two would be the hardest. the second two should be a lot faster.

[Blk EX Coupe]

@ jay snap, is it from your tubro?

@boostin dc2,

those wheels look great on there, what are they?

His wheels look like Konig Countersteer R

[JDMxDB8]

Got a new clutch master cylinder. The old one went out.

[NorcoAccord]

Taking the civic to AAA to change ownership. I am going to miss that car, I sold her for 1850.00. but I am saving about 400 dollars a year on insurance for her, but I will be driving my accord more so there goes that savings. Ohh well and one last thing tonight I pack and tomorrow I leave for New York. I miss SoCal already.