EXT: A Complete USDM Black Housing DIY W/ PICS!!! (56K Be Warned!!!)

[wallycb7]

hey jw???? on the 92 accords bumpers can i take the headlights out without taking the bumper off??

[PointBlank]

hey jw???? on the 92 accords bumpers can i take the headlights out without taking the bumper off??

Negative.

[wallycb7]

damn thats sux cause my bumper is a b...h to take off

[0to60n2weex]

I did the DIY ... i just wanted to show it off. Everything came out good. I used that yellow stained glass spray paint. That stuff was awesome. I also did my blinkers... they were clear (90-91 stanley's).

[BlitzCB7]

i dont have to mask off the black while spraying the stained glass paint right?

Sorry I just wanted to doublecheck

[The-Gr8-Ox]

i dont have to mask off the black while spraying the stained glass paint right?

Sorry I just wanted to doublecheck

i didnt, not needed. If you did, let the paint cure for 24 hours so it doesnt come up with the tape

[ddcb7]

im going to start this tomorrow..will see how far i get

[T04ECB7]

i blackhoused my headlights and they turned out great but i didn't do the yellow highbeams. great diy!

[JaberCB7]

hey great write up but i think using engine paint from local autozone/advance is better than the krylon bbq paint, i tried it to see if it be easier/better but the paint kept peeling off even after securing the tape, using str8 edge against the tape to seperate paint from tape and even peeling in diffrent directions and still had a small piece rip here and there but since ive always used the engine paint i redid it with it and just to test a theory i pulled tape hard and not a single tear....but overall great writeup

[carpet47]

Beams

So ok in case the question wasnt already asked do I need to upgrade the bulb to a brighter one or can i keep the stock bulbs for the black housed

The corner markers work the same way mine are from the 90 cb

[bcjammerx]

...

Laters.

...

Laters.

...

Laters.

...

Later.

...

Laters.

HA HA HA...someone is trying to steal TypeG's catchphrase

oh yeah...good job btw

[Djmoua]

So uh I just finished my blackhousing...and turned out only ok...

As in...as I was taking off the tape...bits and pieces of the reflector paint came off.

What do you guys suggest if not mentioned already?

[Djmoua]

Nobody?

[The-Gr8-Ox]

are you talking about the black? try to remask it and paint it,

if the actual reflectance came off, well that's another issue.
there's two things you can do.
1. if its not horrible, let it be and see if it affects your light output, more than likely it wont if its tiny scattered spots. if you have large chunks, your kinda S.O.L.
2. go to the junkyard and find another set and retry the blackhouse, just make sure to use blue drywall tape to keep it from stripping the reflectance.

hope this helps

-Ox

[Djmoua]

are you talking about the black? try to remask it and paint it,

if the actual reflectance came off, well that's another issue.
there's two things you can do.
1. if its not horrible, let it be and see if it affects your light output, more than likely it wont if its tiny scattered spots. if you have large chunks, your kinda S.O.L.
2. go to the junkyard and find another set and retry the blackhouse, just make sure to use blue drywall tape to keep it from stripping the reflectance.

hope this helps

-Ox

Ohhh blue dry wall tape I shall use instead! Thanks dude, but only lucky this was my stock headlights i practiced on rather than my JDM 1pcs haha. Good practice, ha shit...thanks again.