Announcement

Collapse
No announcement yet.

P5ylance : 1992 Accord EX

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Mike1357
    replied
    This car looks fantastic! I think everything flows better on the black car.

    Leave a comment:


  • P5ylance
    replied








    Leave a comment:


  • Domesticated
    replied
    Those rear knuckles probably make it easy to fit the TL 17x8s right?

    Leave a comment:


  • Jarrett
    replied
    I had 3.2TL rear knuckles that give a track width increase of 30mm in the rear as the hubs are 15mm taller on either side. Going from a 14mm Accord sway bar to a 16mm Vigor rear sway bar with urethane mounting bushings gave a much more noticeable difference in the behavior of the rear suspension than the track increase did. I don't even know if I felt anything considerable at all.

    Leave a comment:


  • Lucien
    replied

    Leave a comment:


  • P5ylance
    replied
    yeah, width increased about 1inch per side. thats an additional 50.8mm of track width. cant wait to feel the effects on handling





    Last edited by P5ylance; 06-05-2015, 03:47 AM.

    Leave a comment:


  • P5ylance
    replied
    its a treat because im confirming that all you need are the arms themselves and it all works. you dont need the knuckle, you dont need the trailing arm, you dont need the subframe. you keep all your CB stuff and just swap the CD arms. i checked the trailing arm part numbers and theyre the same.

    Leave a comment:


  • P5ylance
    replied
    people are afraid theyll bind. those people didnt grab the toe arm as well. if you use both, youre golden.

    well, stance yes, but they do have their merit. im using them to increase my track width in the rear, and as long as you correct the negative camber by extending your upper control arm via some form of kit or washer, you will have a wider track width. i rolled my fenders flush, corrected my camber maxed out that the inner wheel well has clesrance for, and im still slightly negative after 3 washer stack and spc camber kit. thats how effective these arms are in improving the rear wheel base.im at 5.37mm left of gap between my 17x7 +35 wheels, just right for a 5mm spacer.

    and no my wheels aren't butterflied out, i aim to run no more than -1.5 camber if i can help it, im shooting for -1

    Leave a comment:


  • Jarrett
    replied
    How is this a treat? I thought people knew this.

    I'm assuming this is being touted for stance purposes.

    Leave a comment:


  • P5ylance
    replied
    for those who follow my thread, here's a treat. CD rear lower control arms and toe arms are a direct fit. You must use both the toe and control arm from the 94-97 accord for it to work. They are longer than CB arms.

    Leave a comment:


  • 802cb7
    replied
    Good, I finally found a place that has some. I wanted the all chrome ones like yours but I guess those have been discontinued for quite some time now. So I'mm getting the black housed ones. I like the factory look of them. Are they glass? Mine should be showing up any day now, I also ordered an H.I.D. kit to go with them. Funny, I remember when you could walk into advance auto parts and buy these off the shelf ca. 2002 lol. idk, they seem legit.

    Leave a comment:


  • P5ylance
    replied
    omg i loved them, cant wait to reinstall them on this black one!! cutoff was pretty good, and they were reallu nice circles... just really good build quality headlights!!

    Leave a comment:


  • 802cb7
    replied
    How do you like the headlights on the white accord?

    Leave a comment:


  • P5ylance
    replied
    thanks accorn!! tryna get it back up to speed, the only thing holding me back is money for the full rebuild and getting it set up... gonna be about a few months of saving xD but got my debts listed and it looks like we should be cruising through

    it was just tedious DRAWING it lol, i think thats what gets most people... they just wanna plug and chug. i might make an excel file instead cuz handwriting is the tedious part haha... gotta love 120WPM!!

    Leave a comment:


  • sonikaccord
    replied
    Nice wiring diagram. I don't know why everyone thinks that wiring is hard, you did a good job!

    Leave a comment:

Working...
X