zedjr10
CB7tuner Member
Last Activity: Today, 01:12 AM
Joined: 01-24-2017
Location: Denver, Colorado
-
What is a good grease substitute for tranny spline
I ran out of grease that is supplied with the clutch kit. I got some high temp from autozone. Will that work? -
i was impatient cause i had nothing to hold the teeth on flywheel. The pressure plate is torqued right. That milwaukee right angle impact can't torque a short well light socket past 110 probably. I doubt...Leave a comment:
-
overtorqued flywheel bolts
I put my flywheel on using an impact. It is an electric impact with a torque rating of 200ft lbs max. It was a little light spline socket that probably can only get about 120 ft lbs of max torque. So... -
The top part i pulled out. Am wondering what goes around that shaft i pulled out. Once i pulled it out some half circular shaft fell out. I will try to get a pic of it....Leave a comment:
-
Did i lose something in the speed sensor when pulling i tout of tranny?
upon removing my tranny i pulled speed sensor out. I first undid the top two smaller bolts that just take top part out. Some small round metal sleeve i think fell out. I realized this was wrong part to... -
i would think so too. Just wanted to make sure....Leave a comment:
-
Does the luk flywheel already have center bushing in it?
I just put on a new luk flywheel. Do those things already have center bushing in them. I see one in the clutch kit and am wondering now if i got to pull off flywheel and put that bushing in there. I t... -
i just banged it in with a rubber mallet and the old one on it till it went all teh way in. I think before it was flush with outer surface. Which is jsut a mm or 2. I doubt this will matter, right?...Leave a comment:
-
good to hear as no worry about it leaking once i put it in. New tranny, new clutch, flywheel and crank seal. Oh boy. Car is mechanically new almost....Leave a comment:
-
i was told this was so hard and had to lineup perfectly and some special tool was need to set it in their right or something. This is easy!...Leave a comment:
-
yes it looks just like an axle seal or the top camshaft seal but was told that it is quite tricky to put in. It doesn't look it at all. Is there a special tool. Was just planning on prying it out with...Leave a comment:
-
gotchya. Is that rear crank seal as simple as it looks to replace and get right in there....Leave a comment:
-
How to replace rear crankshaft seal
I got flywheel out and am looking at rear crank seal. It looks like it is leaking. Was told these things are hard to replace but it looks easy. Any tips in doing this? -
what strength threadlocker for flywheel and pressure plate
I am changing my clutch and flywheel and am wondering what strength threadlike to get. High stregnth or medium. Was thinking high strength myself but wanted to ask. -
it is off. What a pain. Had to take dogbone off for the extra 2 inches. What a tight fit. How am i going to get it back on i wonder now. Now got to replace the clutch and flywheel then put a new tranny...Leave a comment:
-
I GOT IT SEPARATED FROM ENGINE BUT tranny SPLINDLE not all the way out from clutch cover. That tranny shifter is knocking up against the brake lines. I think if i drop the dog bone engine mount or the...Leave a comment:
-
Oh get to now. I dont actually remove the rear mount itself. Just the tranny from it....Leave a comment:
-
And why is that. Are u talking about the cross member? Does the rear mount and intake manifold bracket because of? Am just a bit lost as to why....Leave a comment:
-
Question regarding tranny removal
I am removing my manual tranny and am wondering why the manual tells me to take off rear motor mount and intake manifold bracket. Is this really necessary?
No activity results to display
Leave a comment: