After redoing this whole ac system almost and evacuating the system. I can put 3 12 oz cans in system and still pressures read like my system is low. It reads 40 on low side and 230 on high side with 94 degrees temp. Each can i add i probably am losing 2 oz but if that is true i got already 30 oz. It should be overcharged. WHen i did evacuate it only reached -24 in hg. I am told it must reach at least -29. I thought it was just a gauge malfunction. My pump is only 1.8 cfm. Would this have anything to do with it? I live in Denver so i wonder if this has anything to do with it.
Announcement
Collapse
No announcement yet.
AC low and high pressure gauge readings still low after 3 cans
Collapse
X
-
Originally posted by Ghostwhite View PostPretty soon you'll have the whole first page the Tech sub-forum. Is it really necessary to create a new thread for every single issue instead of having an AC thread or just doing a build thread?
Had to ask.
It may be that your pump is not strong enough, is it cold? If not it is because you have to much refrigerant, too little or too much and it will not work right. If you didn't vacuum it well enough then it won't be as cold as it should be. 24 should be enough of a pull as long as you held that vacuum for at least 30 mins. If you have a way, then pull a couple ounces of refrigerant out at a time and see if it gets cold.
Comment
-
Originally posted by Rilas View PostYour system is dead? Not working?
What is frozen line issue?
Comment
-
Originally posted by Rilas View PostAfter you get the pressure down, just close the system off and let it sit for a minimum of 30 mins. I've let them sit overnight even just to be sure there are no leaks. Don't disconnect the manifold hoses, just leave it all hooked up so you can keep an eye on the readings.
Comment
-
Originally posted by Ghostwhite View PostPretty soon you'll have the whole first page the Tech sub-forum. Is it really necessary to create a new thread for every single issue instead of having an AC thread or just doing a build thread?
Had to ask.
Comment
-
Originally posted by zedjr10 View PostThe reason is because i look things up by specific questions as i know nobody is going to come out here and tell me step for step what to do. All my questions i try to be specific cause i need to understand all this myself. TUtorials and DIY are great but no way can u follow an exact tutorial step for step. Unless it was like changing your oil and even that varies car to car and circumstances. Things are always different and sometimes just wrong in tutorial. SO i watch many tutorials and ask things i think i need to know. And as with ac systems. I have never done this type of thing before. So i start out not having a clue about nothing. Just a bunch of assumptions.
Step 1) Evacuate system.
Step 2) Disassemble whole system.
Step 3) Flush all the lines while it is all apart.
Step 4) Replace all components (compressor, condenser, dryer, expansion valve.) ALL NEW GREEN O RINGS. PAG oil specs for components are as follows.
Condenser 10cc
Evaporator 25cc
Lines 10cc for each line
Dryer 10cc
Compressor 100cc minus volume of oil drained from old compressor=volume of oil to drain from new compressor
Step 5) Pull a vacuum on the system to -30inHg for at LEAST 30 mins.
Step 6) Charge to 28-30 oz of R-134a Vehicle off, not running.
Step 7) Double check for leaks in the system by watching the manifold gauges. Low side should fall around 30-35 PSI at around 75-80 degrees and high side should be around 225 to 230. THIS IS A BASE LINE FOR PRESSURES! You should be pretty close to that. The ambient temperature and humidity where you are will play a factor in these numbers fluctuating.
Step 8) Enjoy your cold air!
Comment
-
Originally posted by Size9zombie View PostIf you read back thru the other threads you made others and I told you pretty much step by step how to do this.
Step 1) Evacuate system.
Step 2) Disassemble whole system.
Step 3) Flush all the lines while it is all apart.
Step 4) Replace all components (compressor, condenser, dryer, expansion valve.) ALL NEW GREEN O RINGS. PAG oil specs for components are as follows.
Condenser 10cc
Evaporator 25cc
Lines 10cc for each line
Dryer 10cc
Compressor 100cc minus volume of oil drained from old compressor=volume of oil to drain from new compressor
Step 5) Pull a vacuum on the system to -30inHg for at LEAST 30 mins.
Step 6) Charge to 28-30 oz of R-134a Vehicle off, not running.
Step 7) Double check for leaks in the system by watching the manifold gauges. Low side should fall around 30-35 PSI at around 75-80 degrees and high side should be around 225 to 230. THIS IS A BASE LINE FOR PRESSURES! You should be pretty close to that. The ambient temperature and humidity where you are will play a factor in these numbers fluctuating.
Step 8) Enjoy your cold air!
Comment
-
Just so you know, that came straight from the repair manual from our cars. The paper manual, that Honda issued. Some vehicles hold 3 pounds of refrigerant.Last edited by Size9zombie; 06-07-2018, 06:56 PM.
Comment
-
You mean your repair manual.The 30 in/hg vacuum you would never get at 5k feet altitude. More like 24. That is so so basic. I don't see how that would help anyone except a professional who hasn't done it in years and just got to remember. Also the 225 to 230 greatly depends on the ambient temp also. Even cheap crappy tutorials are better than that crap you have.
Comment
-
You JUST quoted me saying that temp and humidity play a factor. NOT MY REPAIR MANUAL. I work for Honda and I grabbed the repair manual off the shelf at the dealer where I work. 5,000 feet may be hard to get 30. I also said in 1 of your other threads that 25 would be fine.Last edited by Size9zombie; 06-07-2018, 07:04 PM.
Comment
Comment