lug studs popped off

[92turboaccord]

alright so you have two moronic responses..one from a teenager and one from an egotistical moron. Why the responded with a ' umm NO ' and ' Have fun' is beyond me but I'll help you out.

Okay so two out of four is bad..but.

You didn't explain specifically which section it was...front or rear.

If it's the front you're going to have to do more work but it's fairly straight forward if you have hand tools. It's time consuming but I'll explain it.

To remove it from the front:

- Remove the caliper and hang it off to the side NOT dangling by the brake hose (you can do damage to it).

- Remove the 32mm axle nut

- Pop the lower balljoint off using a pickle fork and baby sledge hammer

- Slide the axle from the rotor and knuckle assembly and swing the whole assembly to the side.

- Take the baby sledge use an socket extension to drive out the old stud.

To install it on the front:

- Position the new stud in the hole

- Use the hammer and extension to drive it in

- Reinstall wheels and torque them to 80 ft lbs. The lug nut will basically snug the studs in place.

I hope this helps. It's not hard..just time consuming.

and make sure you re-tighten after a few days because the stud might not have seated all the way

[accordboy2011]

so i went to fix the lug stud

and my my hub bearings is no good so i seen whole knuckle for 30 and spindle for 40 which one should i get and wheel it have the hub bearing?

[ExplodingCake]

u have to take the rotor apart from the bearing, to get to the lugnuts.

You Lie!

[Tippey764]

alright so you have two moronic responses..one from a teenager and one from an egotistical moron. Why the responded with a ' umm NO ' and ' Have fun' is beyond me but I'll help you out.

because this is in the wrong section anyways. When people post in off topic for on topic questions it says to me " HELP MY QUESTION IS VERY IMPORTANT AND I NEED EVERYONE TO SEE IT AND HELP ME "

[ChIoVnIdCa]

\" HELP MY QUESTION IS VERY IMPORTANT AND I NEED EVERYONE TO SEE IT AND HELP ME "

[HenRoc]

because this is in the wrong section anyways. When people post in off topic for on topic questions it says to me " HELP MY QUESTION IS VERY IMPORTANT AND I NEED EVERYONE TO SEE IT AND HELP ME "

Tippey simply because 99 percent of the people are in this section...i.e you or me.

I saw the opportunity to help so I did. Obviously you didn't really help the situation by being a fucking douchebag.

Remember you were new once..

So you answer like I did. Not tell the guy have fun and good luck.

[Tippey764]

Tippey simply because 99 percent of the people are in this section...i.e you or me.

I saw the opportunity to help so I did. Obviously you didn't really help the situation by being a fucking douchebag.

So what you're saying is i should post where the most people are? Why even have sections if were all just going to post in 1 forum

When i go to www.cb7tuner.com i want it to take me stright to a big fucking blob of threads because posting in sections isn't as effective because there are less people to help...

Remember you were new once..

So you answer like I did. Not tell the guy have fun and good luck.

But i like being a douche bag. Afterall its just the internet...

Anyways this dude seems incompetentto even tackle such a task. Would you give someone advice on how to rewire a house knowing that they are too incompetent to do so?

[Accrdwgnguy]

and my my hub bearings is no good so i seen whole knuckle for 30 and spindle for 40 which one should i get and wheel it have the hub bearing?

Spindle and knuckle are the same part

Also it is obvious to me that you are looking at used replacements. Why are you gonna replace a worn out part with another worn out part?

[Accrdwgnguy]

But i like being a douche bag. Afterall its just the internet...

Anyways this dude seems incompetentto even tackle such a task. Would you give someone advice on how to rewire a house knowing that they are too incompetent to do so?

This guy IS asking for help, no matter how he is doing it.

Just point him to a DIY or some sort of walk through, or tell him which repair manual to buy. Of course it seems like he doesn't know what he's doing, cuz he doesn't know what he is doing and is asking for help. No need to be a tool about it.

[accordboy2011]

no im puting new parts my cousin work for honda

and he asked did i wanna buy those pieces and i didnt know so i asked and i might have put it in the wrong section i made a mistake im human im not someone rich kid thats sits on the computer im trying to learn so i wont have to ask questions

[deevergote]

Closed. Even though tippey was a bit of a douche about it... he's absolutely right. Your problem is not special. It is not unique. It is not so direly important that you need to post it in the wrong section just because it'll get more views. You are selfish and inconsiderate...

Feel free to repost your question in the correct section, so people that know what they're doing will see it and help you. Typing clearly so we can understand your words might be useful as well, because I can barely read the nonsense you've typed in this thread.