Code 43 On Uberdata Help!

[phatdoughnut]

hmm, this is weird because i threw code 43 for a while on my f22b, with out boost.. but it was my 02 sensor for sure..

[RENR]

im runing midnights map on 1.7/ ill try the closed loop thing today. im using the same harness from the a4. i hope that works. ill be hitting the dyno this satturday!!! yay i hope i hit 250plus trq!

[RENR]

heres the link to 1.7
uberdata

[BustedLX]

yay i hope i hit 250plus trq!

With an F22B at 6psi I'd put your torque just below 200 to the ground. Still very decent but 250 is just alittle high, besides who gives a fuck what numbers it puts down as long as it's fast.

[RENR]

lol, 6psi was on the hack. ill be boosting 10psi on saturday.

hey how the hell do i convert the 1.66 bin to 1.7? i opened the map and checked the closed loop diable, saved it, and then burned it. when i went to try it out, i got a solid cel. so i just burned the 1.66 bin again. what am idoing wrong?

[MRX]

I'll see what i can do for u later tonight RENR...i seem to be the only person that can copy and paste in uber. I'll try out 1.7 myself, i've never run it. 1.8 should be coming out within a couple of months i think, right?

Also busted, how long u gonna be at disney?

[theone]

hmm, this is weird because i threw code 43 for a while on my f22b, with out boost.. but it was my 02 sensor for sure..

same here...when i wasnt boosted, it was my o2sensor....

i was thinkn maybe it has nuffin to do with uberdata chip....
just change the 02sensor

[BustedLX]

Midnight,
I'm leaving today (Tuesday).

Renr,
you'd have to open the StockGSR bin in 1.7 then import P06 and import the maps from your boost tune. Then reset all your options and rev limits.

10psi on a f22B I'd put you at around 230 lt lbs. I'm not hating I'm just tring to be realistic. Please post a dyno sheet when you are done. Also don't use Lujan's dyno to try to calculate accurate torque. They have a bad inductive pick-up and I've seen several Honda's put done 230hp with 1000+ lt. lbs. of torque so try to find a dyno in complete working order, lol.

theon,
Your absolutely right it is most likely a problem with the sensor however you shouldn't even be using it on a boosted engine running a fixed map so why not just disable it, remove the CEL, and save the money?

[RENR]

any past 200 and ill be happy.

[BustedLX]

any past 200 and ill be happy.

On ten psi I think that is a good posibility. Good luck man.

[gdout90accord]

any past 200 and ill be happy.

gyea u will be past 200 cuz accordr33(eric) past 200 already with the f22 and you got f22bdohc so its for sure you'll be around 230

[Accord R33]

just a bigger exhaust than stock would have netted me more than the 6whp to break the 200 mark. without a doubt

[RENR]

i actually messed with the timing a bit made it look a bit smoother and i havent got the code 43 yet.

[phatdoughnut]

You do know that the f22b block is open deck right? so id becareful with the 10psi

[Accord R33]

the f22a is open deck to...actually arnt they pretty much the same block? it should hold 10psi without a problem. i would be carefull going higher than that though