Announcement

Collapse
No announcement yet.

FPR question

Collapse
X
Collapse
 
  • Page of 1
  • Filter
  • Time
  • Show
Clear All
new posts
Previous template Next
    #1

    FPR question

    I finally got a chance to put in my brand spakin new AEM fuel rail today but as i'm putting everything back together I notice that the hose that goes from the IM to the Fuel Pressure Regulator isn't long enough. The instructions said to use the longer hose supplied with the kit but I didn't get one. Any suggestions on where to get another one?


    I also have this question. I can't use my fuel injector wire harness holder anymore since there are no holes on the rail, did anybody use it on thier AEM fuel rail or should I just wrap up the extra naked wires up in some electrical tape and call it a day? Any help is appreciated as I am working on it right now and would like to finish it up soon. Thanks for any responses in advance.
    Tags: None
    #2
    just go to your local automotive store; they sell vacuum lines/rubber tubing in different diameters.

    wrapping up those wires w/ electrical tape will be fine but you can also use wire loom for a cleaner look.
    5.6L V8 32V DOHC
    JDM HERITAGE - US BUILT

    Comment

      #3
      Originally posted by PRIMOCB7
      just go to your local automotive store; they sell vacuum lines/rubber tubing in different diameters.

      wrapping up those wires w/ electrical tape will be fine but you can also use wire loom for a cleaner look.

      Whats wire loom and where can I get it from?

      Comment

        #4
        Originally posted by 1990HybridCB7
        Whats wire loom and where can I get it from?
        same as above, automotive store. wire loom is the plastic tubing used to secure/wrap wires in place. its all over the engine bay in case you haven't noticed
        5.6L V8 32V DOHC
        JDM HERITAGE - US BUILT

        Comment

          #5
          will that loom resist heat over the rail? plastic over hot metal parts doesn't really sound like a good idea.
          1cor10:31
          - 92 LX coupe
          - 96 EX wagon (sold)

          Comment

            #6
            The plastic piece that holds together all the injector wires is practically against my Valve cover and it hasnt ever melted.
            H22 Prelude VTEC 92-96 200 161 10.6:1 87 90 DOHC VTEC 2157 JDM

            190.3whp 155 wtq - with bolt ons, and a dc header

            ET=14.457 @ 94mph w/ 2.173 60Fter

            Comment

              #7
              Originally posted by timmy0tool
              will that loom resist heat over the rail? plastic over hot metal parts doesn't really sound like a good idea.
              itll hold up better than electrical tape...


              - 1993 Accord LX - White sedan (sold)
              - 1993 Accord EX - White sedan (wrecked)
              - 1991 Accord EX - White sedan (sold)
              - 1990 Accord EX - Grey sedan (sold)
              - 1993 Accord EX - White sedan (sold)
              - 1992 Accord EX - White coupe (sold)
              - 1993 Accord EX - Grey coupe (stolen)
              - 1993 Accord SE - Gold coupe (sold)
              Current cars:
              - 2005 Subaru Legacy GT Wagon - Daily driver
              - 2004 Chevrolet Express AWD - Camper conversion

              Comment

                #8
                thanks for all the help guys. finally finsihed her today. Only thing holding me back from finishing was the rubber vacum hose. after searching and searching I just a smaller diameter hose from my job. I still need to tuck those wires away in that wire loom. i'll ask at the advance auto parts tomorrow and see what they got. Again thanks for all your help to those that gave me thier two cents, its really appreciated.

                Comment

                  #9
                  don't know why i didn't mention this before
                  you can get the cover for the fuel injector wire harness thats available for the H22/H23. an old pic, but here is how it looks:

                  5.6L V8 32V DOHC
                  JDM HERITAGE - US BUILT

                  Comment

                    #10
                    Originally posted by PRIMOCB7
                    don't know why i didn't mention this before
                    you can get the cover for the fuel injector wire harness thats available for the H22/H23. an old pic, but here is how it looks:

                    I have that cover. theres just no where to mount it on the new fuel rail

                    Comment

                    Previous template Next
                    Working...
                    X