I am wanting to do a build and i know what im gonna do with the top end, but i was wanting to know some good rod/pistons companies. Also i 've heard of people getting rods cryod. What does this do durability wise and were can you get it done? If you have done it what is your opinion on it? Thanks for all the feedback.
Announcement
Collapse
Please DO NOT Post In The General Section
From this point on until otherwise briefed, posting in the general section of Performance Tech is prohibited. The only thing to remain here will be the stickies. We would just delete this section, but that would cause unintended results.
The majority of the threads created can appropriately be placed in one of the Performance Tech sub-forums or Technical; and the posting of them here is detrimental to the activity of said forums. If you have any questions about where you need to place your thread PM me or one of the other mods.
For the most part you all have caught on without this post, but there have been a few habitual offenders that forced me to say this.
Everyone will get a couple of warnings from here on out, after that I just start deleting threads.
Again if you have any questions, PM me or one of the other mods.
The majority of the threads created can appropriately be placed in one of the Performance Tech sub-forums or Technical; and the posting of them here is detrimental to the activity of said forums. If you have any questions about where you need to place your thread PM me or one of the other mods.
For the most part you all have caught on without this post, but there have been a few habitual offenders that forced me to say this.
Everyone will get a couple of warnings from here on out, after that I just start deleting threads.
Again if you have any questions, PM me or one of the other mods.
See more
See less
Connecting rod questions?
Collapse
X
-
If your only going with the mods you listed then you should look into probe rods. They are good for 300hp and under reliably. I personally have the bisimoto pistons with coatings mated to crower rods.
My Wiretuck/ Insane engine bay
member ride thread
11.86@120mph T66 turbo 612hp F22A
DIVULGE MOTORSPORTS
People can hate all they want, my f22 is faster than yours.
I have literally been on this site for 10 years, I know what i am talking about!
John 10:18 "No one takes it from me, but I lay it down of my own accord. I have authority to lay it down and authority to take it up again. "
Comment
-
Originally posted by turbo90accord View PostIf your only going with the mods you listed then you should look into probe rods. They are good for 300hp and under reliably. I personally have the bisimoto pistons with coatings mated to crower rods.
But from what he listed stock is more than fine for him.
Comment
-
Originally posted by wed3k View Postid go with eagle rods.
Wouldn't that require getting custom pistons with the wrist pin moved up?Originally posted by sweet91accordif aredy time i need to put something in cb7tuner. you guy need to me a smart ass about and bust on my spelling,gramar and shit like that in so sorry.
Comment
-
Originally posted by foamypirate View PostI assume you are talking about the H22 rods? I don't know that they make F22/H23 rods.
Wouldn't that require getting custom pistons with the wrist pin moved up?
Comment
-
Originally posted by 4thgen2door View PostWhat do the probe rods hold up too? What is cryoing rods anyway? Does it work?Originally posted by F22HB View PostWhat brand rod bearings do you guys use?
Cryogenically treating rods rearanges the molecules in the steel theoretically making it stronger by aligning the molecules. yes it works. but not very needed on rods.
im using acl race bearings in my motor.
My Wiretuck/ Insane engine bay
member ride thread
11.86@120mph T66 turbo 612hp F22A
DIVULGE MOTORSPORTS
People can hate all they want, my f22 is faster than yours.
I have literally been on this site for 10 years, I know what i am talking about!
John 10:18 "No one takes it from me, but I lay it down of my own accord. I have authority to lay it down and authority to take it up again. "
Comment
-
-
Originally posted by 4thgen2door View PostIts a stock f22, I dont plan on going 10k or nothing. I plan on doing stage 2 bisi cam, springs and keepers, I/H/E, maybe some msd ignition parts. What will stock rods hold up too?
Comment
Comment