Announcement

Collapse

Please DO NOT Post In The General Section

From this point on until otherwise briefed, posting in the general section of Performance Tech is prohibited. The only thing to remain here will be the stickies. We would just delete this section, but that would cause unintended results.


The majority of the threads created can appropriately be placed in one of the Performance Tech sub-forums or Technical; and the posting of them here is detrimental to the activity of said forums. If you have any questions about where you need to place your thread PM me or one of the other mods.


For the most part you all have caught on without this post, but there have been a few habitual offenders that forced me to say this.


Everyone will get a couple of warnings from here on out, after that I just start deleting threads.

Again if you have any questions, PM me or one of the other mods.
See more
See less

MSD Blaster Coil 2

Collapse
X
Collapse
 
  • Page of 2
  • Filter
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
    #16
    hey "midnite racer x" do u know which of the three wire at the stock coil is a negative or a positive, thats probably why i was misfiring cause i wasn't sure if i connect the right wires.




    =my idea of classic JDM
    to my car page

    Comment

      #17
      ur not gona be using those wires to install it.

      the wires u need to run the blaster coil or SCI module to are under the distributor cap

      the positve wire under the cap is black with yellow strip (one in the middle of the 3 wires)

      and the others is a white wire (negative on the side post)

      once u remove the cap u will see 3 wires that r connected to the distributor, 2 black with yellow strip wirs and a white wire on the corner
      NEED RAP BEATS.....

      www.soundclick.com/akcidentaltrakz

      Comment

        #18
        yea, like I said..wasn't sure on that...it's all mechanical and once it happens, it happens...simply cutting off fuel doesn't stop the motion from occurring...makes sense
        HondaFan81 For Sale Parts (LOW PRICES ON EVERYTHING)

        Comment

          #19
          Originally posted by chiaboi_AcCorD
          [B]hey "midnite racer x" do u know which of the three wire at the stock coil is a negative or a positive, thats probably why i was misfiring cause i wasn't sure if i connect the right wires.
          listen to these guys because my blaster install was a car that did not originally come with an external coil. I simply bought a 92 dizzy and put in the blaster. Follow theone's directions because he has the same car you have. The wires i tapped will most likely not be the wires you will tap. I want good news from you when i get home and check the boards so make it happen!!
          Knowledge is power...in EVERY sense of the word

          FSAE (F Series Accord Enthusiasts) ..."A dying breed thats taking it to the next level" #12

          Comment

            #20
            what ill do this weekend is take my cap off and take a pic of the wires u have to tap for the power and ground for the coil or if u have the SCi (same wires).
            NEED RAP BEATS.....

            www.soundclick.com/akcidentaltrakz

            Comment

              #21
              Originally posted by theone
              ur not gona be using those wires to install it.

              the wires u need to run the blaster coil or SCI module to are under the distributor cap

              the positve wire under the cap is black with yellow strip (one in the middle of the 3 wires)

              and the others is a white wire (negative on the side post)

              once u remove the cap u will see 3 wires that r connected to the distributor, 2 black with yellow strip wirs and a white wire on the corner

              Is yours external or internal?
              =my idea of classic JDM
              to my car page

              Comment

              Previous 1 2 template Next
              Working...
              X