Announcement

Collapse

Please DO NOT Post In The General Section

From this point on until otherwise briefed, posting in the general section of Performance Tech is prohibited. The only thing to remain here will be the stickies. We would just delete this section, but that would cause unintended results.


The majority of the threads created can appropriately be placed in one of the Performance Tech sub-forums or Technical; and the posting of them here is detrimental to the activity of said forums. If you have any questions about where you need to place your thread PM me or one of the other mods.


For the most part you all have caught on without this post, but there have been a few habitual offenders that forced me to say this.


Everyone will get a couple of warnings from here on out, after that I just start deleting threads.

Again if you have any questions, PM me or one of the other mods.
See more
See less

300zx t3

Collapse
X
Collapse
 
  • Page of 2
  • Filter
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
    #1

    300zx t3



    I just picked up one of these in the junkyard
    T03 60 trim compressor and exhaust a/r .63

    I plan to use it on my g23 swap. Any advise
    thanks
    New paint job and bumper 8/8/11
    tsx retrofit
    f22b dohc boosted
    custom gauges pods

    Motivation is one of the keys to life....tell me "can't" and I wll show you I can
    Tags: None
    #2
    should be a good turbo! i used one on my b18b and have full boost by 3200rpm......should come in strong and hold till redline!
    TEH SICKNESS IS RISING

    Comment

      #3
      well thank you for responding...now my build swap shall go on...I am going to install an external waste gate
      New paint job and bumper 8/8/11
      tsx retrofit
      f22b dohc boosted
      custom gauges pods

      Motivation is one of the keys to life....tell me "can't" and I wll show you I can

      Comment

        #4
        turbo looks clean! as long as there is no/minimal shaft play it should be a fun turbo! i would run it on a good log style manifold matched with a 3in DP and 3in exhaust!
        TEH SICKNESS IS RISING

        Comment

          #5
          welll I have to clean mine..I just wanted to show a picture of what I had and the shaft play is minimal to none
          Would a good 2.5" exhaust would be good to start out with. before the 3" because I already have 2.5" setup currently after the down pipe
          thanks
          New paint job and bumper 8/8/11
          tsx retrofit
          f22b dohc boosted
          custom gauges pods

          Motivation is one of the keys to life....tell me "can't" and I wll show you I can

          Comment

            #6
            2.5 will do just find on that turbo, how much psi are you plan on running?
            99 GS300 (Aristo) 2JZ Power


            Bought from:gdout, bb6-sh

            Comment

              #7
              well the stock internal waste gate had a 7.6psi cap...I am still reading and gaining some knowlegdge about turbos and how it operates. I will start at that psi and try not over do it with increasing the psi. What do you think is a safe psi for a g23 stock build
              thanks
              New paint job and bumper 8/8/11
              tsx retrofit
              f22b dohc boosted
              custom gauges pods

              Motivation is one of the keys to life....tell me "can't" and I wll show you I can

              Comment

                #8
                8-12psi IMO is best on a stock block, I would get ARP headstuds so the head doesn't life during boost. Also internal wastgate isn't safe as it could spike easy.
                99 GS300 (Aristo) 2JZ Power


                Bought from:gdout, bb6-sh

                Comment

                  #9
                  what year 300zx is that from?

                  Comment

                    #10
                    Hope he says ooops it's from a 280z, it looks like it cause the 300zx used the t25.
                    99 GS300 (Aristo) 2JZ Power


                    Bought from:gdout, bb6-sh

                    Comment

                      #11
                      Originally posted by Bboy_Trevstuh View Post
                      Hope he says ooops it's from a 280z, it looks like it cause the 300zx used the t25.
                      do you know what an 84 300zx would use? is it a t25 or a t3 like the 280?

                      Comment

                        #12
                        The old 300z uses a t-3 60trim turbo one of my friends have a old Z.


                        updated 3/7/2009=best ET to date: 14.2 (no NOS)

                        Comment

                          #13
                          Is is from a 84 300zx and the exhaust housing has .63 marked on it
                          New paint job and bumper 8/8/11
                          tsx retrofit
                          f22b dohc boosted
                          custom gauges pods

                          Motivation is one of the keys to life....tell me "can't" and I wll show you I can

                          Comment

                            #14
                            nice pick up man, i just got the ct26 from the older supras.
                            I <3 G60.

                            0.5mm Oversized Stainless valves and bronze guides available. Pm me please.

                            Comment

                              #15
                              Yes that turbo is very good,is the . 63 on the exhaust housing?
                              99 GS300 (Aristo) 2JZ Power


                              Bought from:gdout, bb6-sh

                              Comment

                              Previous 1 2 template Next
                              Working...
                              X