Does anyone have the diagram of wiring the cb7 map sensor to an H22a plug? (where to run the wires)
Announcement
Collapse
No announcement yet.
map sensor 4 H22?
Collapse
X
-
^^^ its too big & ugly
here check this topic out mySICKOcb7...
http://www.cb7tuner.com/vbb/showthread.php?t=79283
93 Accord LX Sedan (sold)
01 Civic LX Sedan (sold)-93 Accord EX Wagon (totaled)
93 Accord SE Sedan (sold)-92 Accord EX Sedan (sold)
93 Accord SE Coupe (sold)-97 Accord SiR Wagon (sold)
95 Accord LX Wagon (CURRENT)-05 Impreza WRX Sedan (CURRENT)-02 Ram 1500 (CURRENT)-20 VW Jetta (CURRENT)
Comment
-
The M.A.P. sensor has three wires, the wire colors have stayed pretty consistant throughout Honda's vehicles.
If I remember correctly in our cars the colors are:
White/Blue: This wire is signal to ECU pin D17 (Other common color is White/Yellow or Red/Green) (MAP)
Blue/White: This wire is Ground to ECU pin D21 (Other common color is Green/White) (SG1)
Red/White: The wire is 5v Positive to ECU pin D19 (Other common color is Yellow/White or Yellow/Red) (VCC1)
Hopefully that will help you out somewhat. I'm sorry but I don't have a 5th Gen Lude service manual. If I did I could give you the exact colors.
3 page of the swap thread from bustedlx
Comment
-
most likely, I am telling you from my experience, even when the map is wired right, it normally doesn't work right on out cars, you need to take the little black box apart take the little map sensor run a hose to your intake and make sure the sensor is still plugged. and you'll run perfect,, we tried 3 different h22 map sensors thinking they were bad, when for some reason they just wouldn't work."Self Renewed"
Comment
-
on the black OEM vacuum box. its the plug on the drivers side of the box. it has 3 wires
93 Accord LX Sedan (sold)
01 Civic LX Sedan (sold)-93 Accord EX Wagon (totaled)
93 Accord SE Sedan (sold)-92 Accord EX Sedan (sold)
93 Accord SE Coupe (sold)-97 Accord SiR Wagon (sold)
95 Accord LX Wagon (CURRENT)-05 Impreza WRX Sedan (CURRENT)-02 Ram 1500 (CURRENT)-20 VW Jetta (CURRENT)
Comment
-
^^^ thats one way of doing it. but most people wanna get rid of that box. so you can also just use the H22s map sensors pig tail & tap connect it to the OEM plug on that vac box. in that link I gave ou theres a pic tell which wires go to which
93 Accord LX Sedan (sold)
01 Civic LX Sedan (sold)-93 Accord EX Wagon (totaled)
93 Accord SE Sedan (sold)-92 Accord EX Sedan (sold)
93 Accord SE Coupe (sold)-97 Accord SiR Wagon (sold)
95 Accord LX Wagon (CURRENT)-05 Impreza WRX Sedan (CURRENT)-02 Ram 1500 (CURRENT)-20 VW Jetta (CURRENT)
Comment
-
hmm this is kinda side tracked ..for the map sensor i just extend the red /wht , blu/wht and gr/wht wires and hook it up to the map sensor on the tb . since the vacumn is alreay in the tb where the map sensor is located can this work ? or should i just used the obd1 tb ...is it advisable ? pic below
'' we racing or you just blowing smoke ?''
Comment
Comment