So I just did this swap and my car wont start now. Alittle info about what I am doing, its a 1992 5spd Accord Station wagon with out abs, along with airbag is taken out for different steering wheel. All necessary wires are hooked up. I did not connect the SRS and ABS. Also there's a light green wire called PGM FI. its not connected. The other wierd thing is there is a bright pink wire connected down at my fuse box, was that way when the car came, any Ideas on what that may be. Also any help with my wiring issue would be great
Announcement
Collapse
No announcement yet.
INT : 5th gen Lude Cluster Swap into CB7 EX-R M/T (A/T Avail.)
Collapse
X
-
Red Wagon DD - 1993 EX
http://www.cb7tuner.com/vbb/showthread.php?t=172734
Gray Wagon Project - 1992 LX
http://www.cb7tuner.com/vbb/showthread.php?t=166337
-
So what's the difference between the standard and Type-SH clusters? A shop in town has two automatic clusters, one for a '98 SH and one for a '99 "2.2". Both are listed as $100 on their site. As I don't have ABS, do I go with the SH?Last edited by CyborgGT; 12-26-2010, 07:51 PM.
Comment
-
Originally posted by moetan View PostI got all of my wiring done and so far everything works now I just have to make it fit. turns out that is the hard part. So far I have only cut the inside of the dash, not the vent. I am about to take a little off of the top of the cluster itself. Any other suggestions?I AM VTEC, HEAR ME ROAR!!
Comment
-
Everything apart
Matched the KM from the original cb cluster to the new bb6 cluster...
Cluster installed...
We tried to keep all cutting to a minimum. The back plate behind the cluster was cut to make room for the wiring, 3 holes on the bottom plate to accommodate the tabs on the bottom of the bb6 cluster, and finally 2 notches on the top of the cluster itself in-order to be able to screw in the cover. The side gap is about the same size gap as with the oem accord cluster. Put some electrical tape back there so you can't see the dash foam which normally you could. The gap on the bottom is a bit bigger than oem. The top of the center cover is a few mm off of being completely flush... we just wanted to keep the cutting to a minimum and the gap isn't large enough for it to be a bother.... for now!
If anyone wants i have pictures of how much we cut and the install... maybe i'll just put it up later when I have more time...
Comment
-
Originally posted by 92CB7EX-R View Postdoes anyone have a write-up for the 92 accord EX-R
thx
The best way to wire up this cluster is to access wiring diagrams for both your model CB and the BB6. With correct wiring diagrams, everything should be pretty much straightforward.My pictures/photos will return soon...
Comment
-
Does anyone know which wire it could be if only half of my cluster lights up?
When I turn my lights on only half of the cluster lights up, but when I turn only the corner lights on, the whole cluster lights up.
I'm kind of guessing it's one of the red or red/black wires. Everything else works fine for me.
Comment
-
you have to use the diagrams on page 5 of this thread to see the pin outs for the 93 cb and the prelude.Best to take some pictures of your accord plugs to help match the colors.
Anyone find out how to do the highbeam for the 92/93? According to the diagram, there is two highbeam pins. One for relay, and I cant figure out what the other is. I tried both individually and it doesn't workPSN
Vash744
MRT 1992 EX Coupe "The Jerk"
2009 Subaru Impreza 2.5i Premium Hatchback
2008 Honda Fit Sport (Totaled out - Death by fallen tree)
1993 CB7 Sedan LX (Totaled out)
1991 CB7 Sedan EX (Dead and Junked)
Comment
-
Originally posted by tJoodz View PostDoes anyone know which wire it could be if only half of my cluster lights up?
When I turn my lights on only half of the cluster lights up, but when I turn only the corner lights on, the whole cluster lights up.
I'm kind of guessing it's one of the red or red/black wires. Everything else works fine for me.
I AM VTEC, HEAR ME ROAR!!
Comment
-
Curious..
Did people who did this get their CEL working? Mine worked fine before the swap, and the wireing for it was straightforward. Was there anything extra you had to do for it?PSN
Vash744
MRT 1992 EX Coupe "The Jerk"
2009 Subaru Impreza 2.5i Premium Hatchback
2008 Honda Fit Sport (Totaled out - Death by fallen tree)
1993 CB7 Sedan LX (Totaled out)
1991 CB7 Sedan EX (Dead and Junked)
Comment
Comment