Tnwagn : 1991 Accord LX

[Tnwagn]

Come'on.
More hints than that por favor.

The first page has a Future plans section


Future Stuff:

EXTERIOR:
DIY HID Retrofited JDM 92-93's
Custom front grill w/eyelines
Shaved antenna
Complete Respray of entire vehicle

COMPLETE SUSPENSION OVERHAUL:
Function and Form Type II's Installed
Poly-Bushings (ALL OF THEM!)
Lower Balljoints
Tie rods
OEM Acura 98-99 2.3 CL Premium front hubs
OEM Honda CB7 Bearings
OEM 92-96 Prelude VTEC rotors
SPC Balljoint camber kit Installed
Wicked Rear camber Upper Control Arms Installed
15" 96' Spec ITR's Aquired
APR Extended Studs Aquired
5mm Wheel Spacers Aquired
Stainless Steel Brake Lines
Progress rear sway bar Installed
Front and Rear strut bars Designing

ENGINE (Waaayyyy on down the road):
Honda's newest, freshest, most badass engine available

no pics with the new rims?

New rims will go on after the new year when I have the parts listed above that I need to get before I install the extended studs.



On another note, I was hitting up a sweet road here in Knoxville tonight for a little spirited driving and due to the extreme turns my oil light came on at least 3 times. Werd

[slick]

Function and Form Type II's Installed

damn i want a set of these

[Tnwagn]

Function and Form Type II's Installed

damn i want a set of these

Should have bought some back when they had the group buy pricing on the original batch of Type II's.

[slick]

Should have bought some back when they had the group buy pricing on the original batch of Type II's.

i dont think i was a member of the site then

[Tnwagn]

i dont think i was a member of the site then

Nah, you were.

http://www.cb7tuner.com/vbb/showthread.php?t=76939

The first post is after you joined and I bought mine way after then. I purchased mine early in 08.

[H22WAGON93]

Hows that camber kit in the front working for you. I took off my rims to get ready for the winter and I had some major wear on the inside. Only on the front. Need to figure out something before spring.

[slick]

Nah, you were.

http://www.cb7tuner.com/vbb/showthread.php?t=76939

The first post is after you joined and I bought mine way after then. I purchased mine early in 08.

damn maybe i just never saw it then.... want to show me pics of your setup?

[Tnwagn]

Hows that camber kit in the front working for you. I took off my rims to get ready for the winter and I had some major wear on the inside. Only on the front. Need to figure out something before spring.

The kit I have is pretty good. Definitely strong construction and it has a good amount of adjustability. If you are REALLY slammed (like as low as possible on Type II's) then it bangs, but that's going to happen with any kit. This particular kit has the smallest/lowest profile nut on the top. I would definitely recommend it.

damn maybe i just never saw it then.... want to show me pics of your setup?

No

Just kidding. Crappy front pic and decent rear pic

[91 EX-R]

Hey man, just had to say that the seats and carpet are among the cleanest I've ever seen! I'm probably gonna have to strip my entire car to get mine looking that clean. Very nice.

And when do you plan on throwing the ITR's on?

[Tnwagn]

Hey man, just had to say that the seats and carpet are among the cleanest I've ever seen! I'm probably gonna have to strip my entire car to get mine looking that clean. Very nice.

And when do you plan on throwing the ITR's on?

Eh, everything is pretty clean but there are, in my mind, some MAJOR issues with my interior. The Driver's Seat has worn down in the piping along the edge where you enter the car. The Driver's Side Rear Door Panel also has a pretty unsightly mark/scratch in it from when my system was stolen.

Still, I appreciate the kind words

The ITR's aren't going on until I get my ROH parts, possibly around Christmas. If not then, certainly by Import Alliance in the upcoming Summer.

[JoshM]

Eh, everything is pretty clean but there are, in my mind, some MAJOR issues with my interior. The Driver's Seat has worn down in the piping along the edge where you enter the car. The Driver's Side Rear Door Panel also has a pretty unsightly mark/scratch in it from when my system was stolen.

Quit being anal about your interior.
It's fucking CLEAN!

[90Cb7sleeper]

Ok, so this weekend, i saw a shit load of ITR's in FLA, none of them running extened studs, talked to felipe and after he was done bitching about your wing, he said he had no problems with his wheel studs. so put em on already jeez I almost had my hands on a set of ITR's too. damn money

[JoshM]

I almost had my hands on a set of ITR's too. damn money

I would have gone to your house and stolen them.

[90Cb7sleeper]

All he wanted was a set of stock 90-93 ex wheels and 150.

[JoshM]

All he wanted was a set of stock 90-93 ex wheels and 150.

WHAT?!
Why?
That's a MAJOR downgrade.